MacBook USB-C ports not working? What to check
17 November 2026 · Mac guides
You plug in a drive, a hub or a charger and nothing happens. Or one side of your MacBook works and the other does not. USB-C and Thunderbolt port problems are common, and the good news is that many of them turn out to be the cable, the accessory or a setting rather than the MacBook itself. This guide takes you through the checks you can safely do at home, how to tell whether the port is really at fault, and what to do about it.
First: is it one port, or all of them?
This is the most useful question to answer, because it points in very different directions.
- One port has stopped working while the others are fine. That suggests something local to that port: debris inside it, a worn or loose connector, or damage from the cable being knocked or bent.
- All ports have stopped working at once. That is more likely to be software, a setting, or a fault on the logic board that serves all the ports.
- The ports work for charging but not for accessories, or the other way round. That often points to the cable or the accessory, not the Mac.
Try the same accessory and cable in each port in turn and note what happens.
Rule out the cable and the accessory
USB-C cables all look alike but are not all the same. Some carry only power and slow data. A cable that charges your phone happily may not run an external display or a fast drive.
- Try a different cable, ideally one you know works with that kind of accessory.
- Try the accessory on another computer. If it fails there too, the problem is the accessory.
- Plug the accessory in directly rather than through a hub or dock, at least for testing.
Hubs, docks and power
Hubs are one of the most common causes of "my ports have stopped working". A cheap hub may not supply enough power for a hard drive, or may stop working properly after a macOS update. If macOS shows a message saying USB accessories have been disabled, an accessory is trying to draw more power than the port can give. Unplug it, then try it through a hub that has its own power supply. If everything works when plugged in directly but not through the hub, you have found your culprit.
Check the "Allow accessories to connect" setting
On MacBooks with Apple silicon (M-series chips), recent versions of macOS can ask before letting a new USB or Thunderbolt accessory connect. If you clicked "Don't Allow" by mistake, the accessory will be ignored. Go to System Settings, then Privacy & Security, and look for Allow accessories to connect. Unplug the accessory, plug it back in and look for the prompt.
See whether the Mac can see the device
Hold the Option key, click the Apple menu and choose System Information. Under Hardware, look at USB and Thunderbolt/USB4. With the accessory plugged in, click File then Refresh Information. If the accessory appears here, the port and the Mac can see it, and the problem is more likely to be the drive's format, a driver or the app you are using. If nothing appears in any port with known-good accessories, that points more firmly towards hardware.
A drive that shows up in System Information but not in Finder may need checking in Disk Utility. If it holds files you care about, do not format it in a hurry.
Simple software steps
- Restart the MacBook with the accessory unplugged, then plug it in after you have logged in.
- Install any waiting macOS updates and any dock or display firmware updates.
- Start up in safe mode and test again. If the port works in safe mode, a piece of software that loads at startup may be interfering.
- On Intel MacBooks, a reset of the System Management Controller can sometimes help with power and port behaviour. Apple silicon Macs do not need this; a full shut down and restart does the same job.
Look inside the port, carefully
Fluff or grit can collect inside a port and stop the plug seating fully. Shine a torch into the port. If you can see debris, switch the Mac off and try a short burst from a can of compressed air held upright, or a soft, dry brush. Do not poke inside with anything metal such as a pin or paperclip; you can short the contacts or bend the small tongue in the middle of the port. If a plug feels loose, wobbles or only works at an angle, the connector may be worn or damaged.
Signs it is a hardware fault
- A port that only works if you hold the cable at an angle.
- Visible damage, scorching or green or white corrosion in the port.
- The ports stopped working after a spill, even if the MacBook seemed fine at first.
- No port works with any known-good accessory, even after a restart and in safe mode.
- The MacBook no longer charges from any port, or gets warm near a port with nothing plugged in.
If liquid is involved, stop using the MacBook and get it checked quickly; corrosion can spread over days. See our guide to Mac liquid damage repair.
Can a USB-C port be repaired?
It depends on the model and on where the fault is. On some MacBooks the ports sit on a small separate board that can be replaced. On others they are part of the main logic board, or the fault is in the chips that control power and data to the ports. That is where component-level work matters: we repair logic boards at chip level, which can mean fixing the faulty part rather than replacing the whole board. You can read more on our logic board repair page and our MacBook Pro repair page.
Keep your files safe in the meantime
If your ports have stopped working, your usual backup drive may not be connecting either. Make sure your important files are backed up some other way, such as iCloud Drive or a network backup, until the ports are fixed.
Get a quote
If your MacBook's USB-C or Thunderbolt ports still are not working after these checks, call us on 020 7394 2525 or visit us at 80 Willow Walk, London SE1 5SY, 9am to 6pm Monday to Saturday. We offer bike collection in London and courier collection across the UK.
